Establish Bluetooth (BLE mesh) communication on EFR32MG2 nodes, embedded firmware development

Hi there? how are you? As you can see in my profile reviews, I have rich experience in Electronics as well as Mobile & Desktop app development. Especially, I have completed very similar IoT projects in which mobile communicates with such devices via BLE or wifi several times. I think that I can complete your project perfectly in your timeline. Thanks

Hi, I hope you are doing well. I have done some task with EFRM32 controller. I have reviewed your requirements and would like to discuss the project in more details. Looking Forward, Khawaja

Dear Sir, I am an electrical engineer with 19 years experience in this area . I am going through your requirements and will have some question. I am interested in your project :Establish Bluetooth (BLE mesh) communication on EFR32MG2 nodes, embedded firmware development Please send me a private chat message.

Hi, I am an Electronics and computer science engineer, I have experience working with various prototyping boards, Raspberry Pi, Arduino, mbed (ARM proto board)... as well as developing custom PCBs, you can find some of my projects on my portfolio. Check my portfolio where a mesh network was needed. (irrigation project) I pride myself on ensuring that the customer is satisfied with the quality of the work and strive to sustain good communication and complete the project (5-star reviews/ 100% completion rate) Looking forward to working with you. Regards, Nabil

Hello, i have read the details provided..please contact me to discuss more on the project deadline and some other few things

Hi, Thanks for the Invitation! I am Embedded Firmware Developer. I have good experience with nRF52 BLE chip. I have developed 10+ projects based on it. I have not used EFR32MG2 nodes and BLE mesh yet. I am able to do it if you give me that opportunity. I would like to discuss more your project requirement. Thanks.

Hi Sir/Madam, I hope you are doing great. I have gone through the details, After the first look at the description the job looks pretty much doable. I have rich experience with Bluetooth Low Energy (BLE), C Programming, Embedded Software, Microcontroller. At the moment, I am placing the default bid. Please start the chat so we could have a detailed discussion about it then we can decide the price and time. Thank you

Hi from Las Vegas, I have experience with Silabs EFM32/EFR32 and can work with any MCU of your choice with your instructions. Let's have a chat

Hello, I am senior Microcontroller and Embedded developer and I have plenty of the experience in the smart device development. I have developed the BLE communication between the STM32L475 and Android App and the Wifi between the ESP8266 and Android App. Also I can develop the many kinds of Arduino and ARM, DSP device. As I am Electronic Engineer, I can design the circuit using the Altium Designer. Due to my experience in firmware development, I will bring you the perfect result in time with high quality. I hope we can discuss more details via a private chatting. After you see my profile, you will think I have no experience. I have been developed the complete project, and I have the actual experience. I hope you think again about me I look forward to your response Best regards.

I'm an electronic engineer with more than 15 years of work experience. I work as HW designer; FW and SW developer. As HW designer, I work in Altium, KiCad and Orcad and I have experience in development single MCU (Microchip PIC and ARM Cortex) boards with several digital I/O (GPIO, UART, SPI, I2C, PWM,....) and some analog I/O. I design complete board: power section, MCU section, peripheral section,.... I design also boards with battery power; so I have experience in low power PCB design. I have also experience in commercial boards (Arduino, Raspberry, Beaglebone,...) shields design. I have also experience in bluetooth (both 2.0 and 4.0) PCB design. As FW developer, usually I work in C for Microchip PIC (MPLAB X + XC compilers) and Eclipse + GNU ARM for different ARM Cortex M3/M4 manufacturers (STM32Fx, NXP, EFM32 SiLabs, but I'm ready to learn new frameworks). I work both single task and multi task environment (FreeRTOS and RTX). I write code both for low level driver (GPIO, UART, SPI, I2C, PWM....) management, for high level/final application, for bootloader and for OTA. I work also in "C code" commercial boards Arduino/ESP32/ESP8266 and Linux embedded commercial boards (Raspberry and Beaglebone). I have also experience in bluetooth (both 2.0 and 4.0) programming. As SW developer, I work in C, C++, .NET, Java, and lot of others programming languages. Mainly I work for Windows O.S., but I have experience in Linux development too.

Hi, I have previous experience with the chips EFM32PG12 from silicon labs. I am also aware of simplicity studio which is the development platform for silicon labs products. I have worked on the implementation of Bluetooth mesh, Bootloader functionality according to the requirements, security features, etc., I hope to finish your project ASAP and willing to know much about your requirements.

Dear Client, My name is Terry Chan and I am an expert in embedded system programming using C/C++. I am very interesting and would love to have the opportunity to discuss your project with you. I have the experience in Silabs BGM13S (based on EFR32BG13) platform. I have 3 years of solid experience in SIP phone projects and I have over 15 years of solid experience in embedded system programming. I have developed different kind of electronic products running on Android, Linux and RTOS. I have experience on setting up development environment on Rockchip RK3288 Android SDK, Buildroot, ST STM32F7xx SDK, Nordic nRF5 SDK, Cypress PSoC 4 platform, Silabs BGM13S platform, DSP Group’s DVF99 SDK …