Structural Engineering Jobs

The borough requires anything above a 4 ft. retaining wall to have structural drawings before work can begin. I'm looking at ~90 linear feet with two angles to block off the back of my lot, starting at ~14 ft high hill to one side and rising upwards of 23 ft in the far back. I have an autocad file of the survey / elevation to help, which I can share if / when we come to terms.

Hello I have undertaken the hire of professional services to complete Lime Mortar repointing of a 2-bed end terrace, which is nearing the end of the work. However as I have concerns about the work undertaken for peace of mind, before the job is complete and signed off for payment, I just want to ensure I am paying for a fully professional lime mortar installation of repointing. For example, I just want to make sure that what would be reasonably expected for the undertaking of lime mortar repointing and been fully adhered to and the job is at a satisfactory level. I want to ensure the process undertaken for lime Repointing has been adhered to and I do not need to worry about any defects in the lime repointing such as cracks, holes, gaps, crumbling etc will occur to a reasonab...

I am looking for a geotechnical and structural engineer who can provide detailed design and calculations for a cantilever retaining wall. The wall will be 2.5 meters in height and located on a site with saturated sand (rsat =20kN/m3). The wall must have a design life of more than 20 years. The ideal candidate should have experience in designing retaining walls and be proficient in geotechnical and structural calculations. Skills required for this project include: - Geotechnical engineering - Structural engineering - Retaining wall design - Calculation proficiency - Familiarity with saturated sand soil type. Geotechnical design calculations and structural calculation for reinforcement required. work to eurocode. consider fos of 1.3 (see attachemnet) you havae to do checks for sliding, st...

THEY WILL NEED TO BE BASED IN AUSTRALIA WITH AUSTRALIAN QUALIFICATIONS SO IF YOU HAVE A CONTACT THERE YOU CAN BID. I am in need of an experienced engineer who can design footings for a residential structure. I have soil information and geotechnical reports available for the project. However, I am not sure about the preferred foundation type and would need recommendations. The ideal candidate should have the following skills and experience: - Proficient in structural engineering - Familiarity with residential footing design - Knowledge of various foundation types and their suitability for different soil types - Ability to provide recommendations for foundation type based on soil information and geotechnical reports If you are confident in your ability to provide a safe, efficient, and ...

Modular kitchen designer needed for a modern interior design project. The project scope includes a partial room redesign and consultation and recommendations for the overall design. The ideal candidate will have experience with modern design styles and be able to provide suggestions for a color palette. Looking for someone who is creative, detail-oriented, and able to work within a budget.

We want to add a patio to our home. It will be a gabled structure coming out on our current structure. We need to understand the pitching and sizing etc.

Engineer a porch gable cover with exposed beams. 18'8" long, 178" wide, 9/12 pitch, 16" gable overhang. Shingle roofing, tongue and groove underside

foundation footer for a 15'9" high 12" x 8" x 16" CMU block wall with concrete patio on top. This wall will form a basement room adjacent to the living area dwelling.

Design bridge either box CONCRETE or precast prestressed slab , open girder also steel open girder or pedestrian bridge

I am looking for a freelancer who can create structural plans for a pergola that will be built in an area measuring 120 square feet (10x12). The desired material for the pergola is wood. The area has been identified as Wind Zone 3 and the structural plans should be designed with ASCE 7-16 Wind Zone standards in mind. The ideal freelancer for this project should have experience in structural engineering and be familiar with ASCE 7-16 Wind Zone standards. They should also have expertise in designing and constructing wooden structures.

I am looking for a freelancer to perform a structure simulation using Ansys software. The simulation will be focused on fabricated structures(Electric House moving on traler) and will require experience in the field. The ideal freelancer will have knowledge of the following: - Ansys software - Mechanical engineering - Vibration analysis - Stress analysis -Structural Joints Dimension of E house 12 x 3 x 3.5 m The structure will be made from a steel sections, IGS drawing will be provided upon hiring. The main objective of the simulation will be place E house model on trailer to do vibration analysis, to ensure the structure can withstand any potential vibrations andacting forces during moving on trailer. If you are interested in this project, please provide examples of previous work in t...

need to calculate structural loads, critical stress and failure analysis

I need some small calculation work for "STRUCTURAL LOAD CALCULATIONS ,CRITICAL STRESS CALCULATIONS,FAILURE ANALYSIS " for working model.

We are a small hospital chain and have a inhouse construction and design team, we are looking for a freelance structural engeneer who can work on a fee for service.

I want someone to do Structural load calculations ,Critical stress calculations and Failure analysis for my design

Hardwood Flooring Installation in Living Room I am looking for a skilled professional to install solid wood flooring in my living room, which is approximately 1000 sq ft. The ideal candidate should have experience in hardwood flooring installation and must be able to provide references. Skills/Experience: - Experience in hardwood flooring installation - Ability to work with solid wood flooring materials - Excellent attention to detail - Good communication skills - Ability to work efficiently and complete the project on time Please provide a detailed quote for the project, including the cost of materials and labor. Thank you.

I am looking for a freelancer to design and create shop drawings for a residential building in the construction phase. The ideal candidate should have experience in designing and creating shop drawings for concrete structures. Skills needed: - Experience in designing and creating shop drawings for concrete structures - Knowledge of building codes and regulations for residential buildings Experience required: - Experience in designing and creating shop drawings for residential buildings - Experience in working with concrete materials Materials needed: - Concrete Please provide examples of previous work you have done and your availability for the project.

Structural Load Schedule and Design for Small-scale Project

I need a project for a master bedroom addition to my existing house.

Looking for a skilled individual to create a Primavera plan for a construction project with 50-100 activities. The project has strict deadlines that must be met. Ideal candidates will have experience in construction project management and proficiency in Primavera software. Attention to detail and strong communication skills are also necessary. The project is only structural works with five basements and 26 floors. The basements will be divided into two parts with one part up to ground floor and the other contains the building with 26 floors. Works start from plain concrete , waterproofing then reinforced concrete work

Project details - remove single story comp roof and replace with walk-on deck. I need provide city of Huntingtn Beach with engineer stamped structural plans.

I am seeking a structural engineer or architect who can provide a calculation for the foundation of two steel tanks, a total weighing 70 tonnes. The project is for our existing business and will be located outdoors. The ideal candidate will have experience in structural design and knowledge of steel materials. The project will require the following: - Calculation for the foundation of two tanks - Analysis of soil conditions - Design of reinforced concrete foundation - Knowledge of steel materials and their properties - Ability to adhere to safety regulations and standards. - AutoCAD desing and experience

I am doing a home remodel changing a bedroom and bathroom to a living room and kitchen (granny suite) and adding a bedroom and bathroom to the garage. I need blueprints to use to pull my permits as honeowner contractor. Granite Falls, NC (Hickory area).

I am looking for a freelancer who can help me with a quantity estimate for a forth comming project. The project requires someone with past work experience in quantity estimation for Steel works. The project needs to be completed ASAP, so the ideal freelancer would have the availability to start right away. Skills and experience needed: - Past work experience in quantity estimation for businesses - Ability to work under tight deadlines - Strong attention to detail - Good communication skills to discuss project requirements and progress updates - Knowledge of relevant software/tools for quantity estimation If you have the required skills and experience, please include your past work in your application. Thank you!

I need a mechanical engineer to carry out engineering on attached project at 4 - 6 Eastwood st -- to satisfy Victorian standards for building permit and use for heating and cooling on job. I need the plans drawn and stamped

Staying within permitted development (going 3m back) and with a very simple design, I am looking for a structural engineer to survey and provide drawings for my builder to commence the project. Many thanks.

I have a BOQ for a ongoing project in which i need to estimate the steel works quantity with weight analysis for each individual item. The work is very basic , like steel hand rails, decks, CAT ladders etc.

I have a partially completed patio that now needs a permit. The plot map, framing, and elevation drawings are done. Need to complete floor plan, Constuction section, foundation, structural details and plan.

Structural design needed for top slab's shuttering and scaffolding using plywood material and scaffolding material. The top slab is 10 m x 5 m and requires a medium load-bearing capacity. Ideal skills and experience for the job include expertise in structural engineering and experience with wood material for construction.

There is one story edification over a bridge. Pillars are the concrete and the beams are the steel. I need someone who knows CSI Bridge. We will work together in this project

My project requires the expertise of a civil engineer who has experience with designing and constructing large and complex structures using steel. This project will demand great attention to detail, with a focus on accuracy and quality workmanship. The engineer should have significant experience in structural design, utilizing steel as the primary material. Additionally, experience in site development and transportation engineering means the optimal person for the job will have a range of skills in order to ensure the project is completed successfully and efficiently. Overall, this is a large and complex project, with specifications that require the precision of an experienced civil engineer.

Event center just under 13,000 square feet. Stair case should be CENTERED I also want a loft upstairs for people to sit and relax and an office upstairs 3D rendering is a must

need civil for foundation plan/boq of simple porch 25x20 feet

I am looking for an experienced and knowledgeable freelancer to do a vehicle load analysis on a specific structure using SAP2000. The analysis will consider static loads and is for structural design purposes. I will supply the overall dimensions, material data, vehicle and design code data so that the freelancer can do the appropriate analysis. The final deliverable of this project should be a report explaining the results of the analysis and methods used. Experience with SAP2000 is highly preferred for this project.

I need the help of a Mechanical or Structural engineer who can help me with stress analysis of a Piping system and Generate Detailed reports using CAESAR II quite urgently, if you have the skills, kindly reach out to me

I am purchasing a steel shop building from my manufacture in China. I am looking to get engineer plans, stamped by a licensed engineer in Ohio for permitting purposes.

I am not skilled in cad but i do much design work. The previous engineer i was working with has been rather disappointing. It has seem to hit a wall and there were some big mistakes. I need to verify some calculations and detail concepts to put on the drawing so i can obtain stamps and seals. Footer Detail CMU Column Detail Wall Section Detail Truss Detail Wood floor framing detail Uplift connector detail Cantilever detail Foundation Plan Truss Plan Floor Framing Plan Roof Framing plan Elevation Views Specs with data and calculations Foundation specs with calculations and factory of safety Truss calculations The structure is 24x56 and i have some cad and revit models. Just need to conclude it. If you have availability i will send you what I have, you can let me know if you can h...

I am in need of a Structural Designer with Precast Experience in USA projects to design parking garages for my upcoming project. The ideal candidate should have experience in designing precast parking garages. Design Codes and Regulations: I will provide specific design codes and regulations to follow for the project. Project Timeline: The project timeline is more than 4 weeks. Skills and Experience: Ideal skills and experience for this job include: - Experience in designing precast parking garages - Knowledge of specific design codes and regulations - Ability to work on a project with a timeline of more than 4 weeks.